Enterasys RoamAbout Guía de instalación Pagina 1

P/N 9034169-07Installation GuideEnterasys RoamAbout®RBT-1002, RBT-1002C, RBT-1002C-EU and RBT-1002-EUWireless Access Point

COMPLIANCESVIIIHigh power radars are allocated as primary users (meaning they have priority) of the 5250-5350 MHz and 5725-5850 MHz bands. These radar

COMPLIANCESIXCountries of Operation & Conditions of Use in the European CommunityThis device is intended to be operated in all countries of the Eu

COMPLIANCESXOperation Using 5 GHz Channels in the European CommunityThe user/installer must use the provided configuration utility to check the curren

COMPLIANCESXIdescribed in this document.• This device employs a radar detection feature required for operation in the 5 GHz band. This feature is auto

COMPLIANCESXIIRBT-1002C, RBT-1002C-EUFederal Communication Commission Interference StatementThis equipment has been tested and found to comply with th

COMPLIANCESXIIIOperating FrequenciesThe user must use the configuration utility provided with this product to ensure the channels of operation are in

COMPLIANCESXIV• 7 cm (D=0.06494 m) is the minimum distance between the EUT and human body to meet the E-field strength of 61V/m.• The 5 GHz Turbo Mode

COMPLIANCESXVCountries of Operation & Conditions of Use in the Asia, Pacific, and Middle East Communities This device is intended to be operated i

COMPLIANCESXVIOperation Using 5 GHz Channels in the Asia, Pacific, and Middle East CommunityThe user/installer must use the provided configuration uti

COMPLIANCESXVIIDeclaration of Conformity in Languages of the European CommunityEnglish Hereby, Enterasys, declares that this Radio LAN device is in co

COMPLIANCESXVIIIGerman (DE) Hiermit erklärt Enterasys, dass sich dieser/diese/dieses Radio LAN de-vice in Übereinstimmung mit den grundlegenden Anford

COMPLIANCESXIXSafety CompliancePower Cord SafetyPlease read the following safety information carefully before installing the access point:WARNING: Ins

COMPLIANCESXXSwitzerland The supply plug must comply with SEV/ASE 1011.U.K. The supply plug must comply with BS1363 (3-pin 13 A) and be fitted with a

COMPLIANCESXXIHazardous SubstancesThis product complies with the requirements of European Directive, 2002/95/EC, Restriction of Hazardous Substances (

COMPLIANCESXXII

XXIIITable of ContentsChapter 1 IntroductionPackage Checklist ...

XXIVContents

1-1Chapter 1IntroductionNote:The RBT-1002C-EU, although listed in this document, is not available until March 2008.Aunque el modelo RBT-1002C-EU est

Introduction1-2Complementary Code Keying (CCK) modulation technology to achieve a communication rate of up to 11 Mbps. The access point supports a 54

Hardware Description1-3Hardware DescriptionTop PanelRear PanelAntennasLED IndicatorsSecurity Slot5 VDC Power SocketRJ-45 Port,PoE ConnectorReset Butto

INOTICEENTERASYS NETWORKS reserves the right to make changes in specifications and other information contained in this document and its web site witho

Introduction1-4Component DescriptionAntennasThe access point includes integrated diversity antennas for wireless communications. A diversity antenna s

Hardware Description1-5LED Status DescriptionPower Solid green Normal operation. All of the following are true:• Management link with a wireless switc

Introduction1-6Security SlotThe access point includes a Kensington security slot on the rear panel. You can prevent unauthorized removal of the access

Hardware Description1-7However, when connecting the access point to a workstation or other device that does not have MDI-X ports, you must use crossov

Introduction1-8Features and Benefits• Local network connection via 10/100 Mbps Ethernet ports or 54 Mbps wireless interface (supporting up to 127 mobi

2-1Chapter 2Hardware Installation1. Select a Site – Choose a proper place for the access point. In general, the best location is at the center of your

Hardware Installation2-2Mounting on a wall or the ceiling– The access point should be mounted only to a wall or wood surface that is at least 1/2-inch

Hardware Installation2-3Then screw down the fastening screw to secure the access point to the bracket.3. Lock the Access Point in Place – To prevent u

Hardware Installation2-44. Connect the Ethernet Cable – The access point can be wired to a 10/100 Mbps Ethernet network through a device such as a hub

Hardware Installation2-56. Observe the Self Test – When you power on the access point, verify that the Power indicator stops blinking and remains on g

IIEnterasys Networks, Inc.Firmware License AgreementBEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT,CAREFULLY READ THIS LICENSE AGREEMENT.This docume

Hardware Installation2-6To remove the bezel, grasp both sides and gently pry away from the fastening slots located on each antenna side. Pull the beze

A-1Appendix ATroubleshootingFor troubleshooting information, refer to the RoamAbout Mobility System Software Configuration Guide.

TroubleshootingA-2

B-1Appendix BConfigurationAll configuration of the RBT-1002 is done from the RoamAbout wireless switch and the RoamAbout Switch Manager interface.Refe

ConfigurationB-2

C-1Appendix CCables and PinoutsTwisted-Pair Cable Assignments For 10/100BASE-TX connections, a twisted-pair cable must have two pairs of wires. Each w

Cables and PinoutsC-2The following figure illustrates how the pins on the RJ-45 connector are numbered. Be sure to hold the connectors in the same ori

Twisted-Pair Cable AssignmentsC-37 -48V feeding power (Negative- Vport)8 -48V feeding power (Negative- Vport)Note: The “+” and “-” signs represent the

Cables and PinoutsC-4Straight-Through WiringBecause the 10/100 Mbps port on the access point uses an MDI pin configuration, you must use “straight-thr

D-1Appendix DSpecificationsNote:The RBT-1002C-EU, although listed in this document, is not available until March 2008.Aunque el modelo RBT-1002C-EU es

IIIin part, including for reasons of error correction or interoperability, except to the extent expressly permitted by applicable law and to the exten

SpecificationsD-2RBT-1002-EU ETSI: 1-13 France: 10-13RBT-1002C-EU ETSI: 1-13 France: 10-13Maximum Clients127 total clients for the APOperating RangeRe

General SpecificationsD-3 4.92 ~ 4.98 GHz Japan 5.04 ~ 5.08 GHz Japan802.11b:2.4 ~ 2.4835 GHz (US, Canada)AC Power AdaptersInput: 100-240 A

SpecificationsD-4CompliancesRBT-1002, RBT-1002CFCC Class B (US)ICES-003 (Canada)RBT-1002C-EU, RBT-1002-EURTTED 1999/5/ECRadio Signal CertificationRBT-

General SpecificationsD-5Transmit Power 16 QAM (36 Mbps) -77 -77 -78 -7864 QAM (48 Mbps) -73 -73 -73 -7364QAM(54 Mbps) -69 -70 -70 -67IEEE 802.11gData

SpecificationsD-648 Mbps 17 17 17 1754 Mbps 12 17 17 16IEEE 802.11g Maximum Output Power (GHz - dBm)Data Rate 2.412 2.417~2.462 2.4726 Mbps 20 20 189

Index-1Aantenna description 1-4antennas, positioning 2-5Bbezel 1-2attaching and removing the bezel 2-5Ccableassignments C-1crossover C-4straight-throu

IndexIndex-2Ssecurity slot 1-6self test 2-5site selection 2-1specifications D-1straight-through cable C-4system defaults 1-8Ttroubleshooting A-1

IV5. UNITED STATES GOVERNMENT RESTRICTED RIGHTS. The enclosed Program (i) was developed solely at private expense; (ii) contains “restricted computer

V8. AUDIT RIGHTS. You hereby acknowledge that the intellectual property rights associated with the Program are of critical value to Enterasys and, acc

VI13. SEVERABILITY. In the event any provision of this Agreement is found to be invalid, illegal or unenforceable, the validity, legality and enforcea

VIICOMPLIANCESRBT-1002, RBT-1002-EUFederal Communication Commission Interference StatementThis equipment has been tested and found to comply with the