Enterasys Enterasys Matrix 9033989-06 Guía de instalación Pagina 66
- Pagina / 90
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Overview of DFE Module Shutdown Procedure
4-10 Troubleshooting
Recommended Shutdown Procedure Using OFFLINE/RESET
Switch
BeforepullingaDFE moduleoutofachassis,
pressortaponitsOFFLINE/RESETswitchforlessthan1 second.
ItsCPULEDchangesfromsolidgreentoblinkingbetweengreenandamber,indi cating
thatthemoduleisshuttingdown.Attheendoftheshutdownroutine,theCPULED
changesto
a67%/33%sequenceofamber/off,respectively,indicatingthemoduleisina
haltstate.Inthistimeitissafetorestartorremovethemodulefromthechassis.
WhenacontrolledshutdownisinitiatedfromtheOFFLINE/RESETswitch,youhave60
secondsfromthetimetheCPUstartsalternately flashing
amber/offuntilthedevice
automaticallyrestarts.
Last Resort Shutdown Procedure Using OFFLINE/RESET Switch
ToresetaDFE modulewithoutitperforminganorderlyshu tdownroutine,
pressandholdthe OFFLINE/RESETswitchforapproximately6seconds.
PullinganyDFE moduleoutofthechassisbeforeithasbeenshut downisnot
recommended.Theonlysafetimetopullamoduleoutofthechassisisafter
the
completionofashutdownandthemanagementLEDisalternatelyflashingamber/off.
Caution: Do not pull any DFE module out of an operating chassis before it has completed
its shutdown routine.
Precaución: No retire los módulos DFE del chasis en funcionamiento hasta que no se
haya terminado con la rutina de apagado.
Note: The only safe time to pull a DFE module out of the chassis is when the CPU LED
is alternately flashing amber/off. Otherwise, system operation will be interrupted.
Caution: This method of shutting down a DFE-Gold module is not recommended except
as a last resort, because all processes currently running on the module will be interrupted
resulting in loss of frames.
Precaución: No se recomienda utilizar este método para apagar los módulos DFE- Gold.
Recurra a él sólo como último recurso, puesto que interrumpe todos los procesos del
módulo en funcionamiento, lo que podría resultar pérdidas de frames.
- Enterasys Matrix 1
- orcontact 5
- (Circuit Modules) 6
- (Circuit Breakers) 6
- VCCI Notice 7
- BSMI EMC Statement — Taiwan 7
- Safety Information 8
- Class 1 Laser Transceivers 8
- Declaration of Conformity 8
- Contents 13
- Chapter 4: Troubleshooting 14
- Appendix A: Specifications 14
- About This Guide 17
- How to Use This Guide 18
- Related Documents 18
- Getting Help 20
- Introduction 21
- DFE-Gold Module 22
- 1-4 Introduction 24
- Connectivity 25
- Management 25
- Standards Compatibility 26
- LANVIEW Diagnostic LEDs 26
- Network Requirements 27
- 10BASE-T Network 28
- 100BASE-TX Network 28
- Installation 29
- Installation Site Requirement 30
- Unpacking the DFE Module 30
- Example 1 (Figure 3-1, A) 32
- Example 2 (Figure 3-1, B) 32
- Example 3 (Figure 3-1, C) 33
- Example 4 (Figure 3-1, D) 33
- Example 5 (Figure 3-1, E) 33
- 3-6 Installation 34
- 3-8 Installation 36
- 4 Metal back panel 37
- into Matrix N3 or N5 Chassis 38
- FAST ENET 39
- 3-12 Installation 40
- Connecting to the Network 41
- 3-14 Installation 42
- 2 Other device port 44
- Verifying PoE Port Status 45
- What Is Needed 46
- 3-20 Installation 48
- Connecting to a Modem 49
- 3-22 Installation 50
- RJ45 Connector (Female) 51
- DB9 Connector (Female) 51
- DB25 Connector (Female) 51
- DB25 Connector (Male) 52
- Enterasys 53
- Completing the Installation 54
- 3-26 Installation 54
- 3-28 Installation 56
- Troubleshooting 57
- Using LANVIEW 58
- 4-2 Troubleshooting 58
- Viewing the PoE Port Status 59
- 4-4 Troubleshooting 60
- 4-6 Troubleshooting 62
- Troubleshooting Checklist 63
- 4-8 Troubleshooting 64
- 4-10 Troubleshooting 66
- Specifications 67
- Item Specification 68
- COM Port Pinout Assignments 69
- Regulatory Compliance 69
- A-4 Specifications 70
- Required Tools 71
- Setting the Mode Switches 72
- 1 2345678 73
- 48V --- 20A MAX 74
- OPTIONAL 74
- WER INPUT 74
- Removing the Safety Cover 75
- AST ENET 76
- Removing the DRAM SIMM 78
- Installing the DRAM SIMM 79
- DIMM Replacement Procedure 80
- Installing the DIMM 81
- --- 20A MAX 82
- Reinstalling the Safety Cover 83
- Overview 85
- Proprietary PD Detection 86
- Power Interface 86
- Front Panel 48 Vdc Interface 86
- PoE Port Status LEDs 87
© 2020, manymanuals.es. Todos los derechos reservados | 0.019 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales