Enterasys 5C105 Guía de instalación descargar pdf (Pagina 32)

Inicio
Enterasys
Módulos de conmutación de red
5C105
Guía de instalación

Descarga
Compartir

Compartiendo
Añadir a mis manuales
Imprimir

Installing Optional 5PIMs

3-4

3.2.1 Removing the Coverplate

Refer to Figure 3-1 and proceed as follows:

1. Attach the antistatic wrist strap (refer to the instructions on the antistatic wrist strap package).

2. Place the module

➀ on an antistatic pad on a sturdy flat surface.

Figure 3-1 Removing the Coverplate

3. Remove the two screws ➁ fastening the coverplate ➂ to the module front panel ➃. Save the

two screws for installing the 5PIM.

4. Remove the screw ➄ fastening the board to the module chassis. Save the screw for installing

the 5PIM.

➀

Module

➂

Coverplate

➄

Fastening screw

➁

Coverplate screws (2)

➃

Module front panel

36771_13

1 2 ... 27 28 29 30 31 32 33 34 35 36 37 ... 77 78

5H152-50 and 5H153-50 1
Fast Ethernet Modules 1
Installation Guide 1
FCC NOTICE 4
INDUSTRY CANADA NOTICE 4
VCCI NOTICE 4
CLASS A ITE NOTICE 4
ENTERASYS NETWORKS, INC 6
PROGRAM LICENSE AGREEMENT 6
DECLARATION OF CONFORMITY 8
Contents 9
INSTALLATION 10
TROUBLESHOOTING 10
SPECIFICATIONS 10
MODE SWITCH BANK SETTINGS 11
GPIM SPECIFICATIONS 11
Figure Page 13
Ta bl e Page 14
About This Guide 15
STRUCTURE OF THIS GUIDE 16
RELATED DOCUMENTS 17
DOCUMENT CONVENTIONS 17
GETTING HELP 18
Introduction 19
5H152-50 20
5H153-50 20
1.1 CONNECTIVITY 21
1.1.3 About the Optional GPIM 21
Table 1-1 GPIM Options 22
1.3 PORT TRUNKING 23
1.4 REMOTE MONITORING (RMON) 23
1.6 FLOW CONTROL 24
1.7 802.1p PORT PRIORITY 24
1.8 MANAGEMENT 24
1.9 SWITCHING OPTIONS 24
1.10 STANDARDS COMPATIBILITY 25
1.11 LANVIEW DIAGNOSTIC LEDs 25
Network Requirements 27
2.2 10BASE-T NETWORK 28
2.3 100BASE-TX NETWORK 28
Installation 29
3.1 UNPACKING THE MODULE 30
3.2 INSTALLING OPTIONAL 5PIMs 31
3.2.1 Removing the Coverplate 32
3.2.2 Installing the 5PIM 33
3.3 INSTALLING OPTIONAL GPIMs 34
3.3.1 Side Clip GPIMs 35
Installing Optional GPIMs 36
3.3.2 Locking Bar GPIMs 38
Preparation 38
3.5 CONNECTING TO THE NETWORK 43
Connecting to the Network 44
Between Switches and End User 45
RJ21 angle adapter 48
RJ21 right-angled connector 48
RJ21 port connector 48
Retaining clips 48
Retaining screws 48
➃ shown in Figure 3-10 are 49
5PIM-G06 50
Multimode fiber optic Cables 51
➀, key side down ➁, into the 52
SC cable connector 53
GPIM-01, GPIM-08, or GPIM-09 53
5PIM interface module 53
Troubleshooting 55
Port 1, Group 1 LEDs 56
Using LANVIEW 57
Table 4-1 LANVIEW LEDs 57
4.2 TROUBLESHOOTING CHECKLIST 59
Troubleshooting Checklist 60
4.3 USING THE RESET BUTTON 61
Specifications 63
A.1.3 Input/Output Ports 64
A.2 5PIM SPECIFICATIONS 64
SC fiber optic connection 65
A.5 REGULATORY COMPLIANCE 66
Mode Switch Bank Settings 67
Mode switch bank 68
• Switch 6 – No function 69
GPIM Specifications 71
Refer to 73
for details 73
Environmental 74

Comentarios a estos manuales

Sin comentarios

Enterasys 5C105 Guía de instalación Pagina 32

Comentarios a estos manuales