Enterasys Matrix N7 7C107 Guía de instalación descargar pdf (Pagina 51)

Connecting to the Network

Matrix DFE-Platinum Series Installation Guide 3-21

Figure 3-12 Four-Wire Straight-Through Cable RJ45 Pinouts, Connections

Between Switches and End-User Devices

Figure 3-13 Eight-Wire Crossover Cable RJ45 Pinouts, Connections Between Hub

Devices

1 RJ45 device port 3 RJ45-to-RJ45 straight-through cable

2 Other device port 4 RX+/RX- and TX+/TX- connections.

These connections must share a common color pair.

1 RJ45 device port 3 RJ45-to-RJ45 crossover cable

2 Other device port

TX+

TX

RX+

RX 2

TX+

TX

RX+

RX

ÀÁ

TX1+

TX2+

RX4-

RX1-

TX4+

RX3-

TX3+

RX2-

TX2+

TX1+

RX3-

RX2-

TX3+

RX4-

TX4+

RX1-

1 2 ... 46 47 48 49 50 51 52 53 54 55 56 ... 93 94

Matrix DFE-Platinum Series 1
Module 7G4280-19 1
Installation Guide 1
VCCI Notice 6
BSMI EMC Statement — Taiwan 6
Safety Information 6
Class 1 Laser Transceivers 6
Declaration of Conformity 7
Enterasys Networks, Inc 8
Firmware License Agreement 8
Contents 11
Chapter 4: Troubleshooting 12
Appendix A: Specifications 12
About This Guide 15
Who Should Use This Guide 16
How to Use This Guide 16
Related Documents 17
Introduction 19
1-2 Introduction 20
7G4280-19 21
5 GROUP SELECT switch 22
Ethernet Interface Modules 23
Connectivity 24
Management 25
Standards Compatibility 26
LANVIEW Diagnostic LEDs 26
Getting Help 26
1-10 Introduction 28
Network Requirements 29
1000BASE-SX/LX/ELX Network 30
1000BASE-T Network 30
Installation 31
Unpacking the DFE Module 32
Removing the Coverplate 33
3-4 Installation 34
Preparation 35
(MGBIC-02) 4 Port slot 37
Removing the Mini-GBIC 38
FTM1 and FTM2 Connectivity 39
Module Placement and Rules 39
Example 1 (Figure 3-6, A) 40
Example 2 (Figure 3-6, B) 40
Example 3 (Figure 3-6, C) 41
Example 4 (Figure 3-6, D) 41
Example 5 (Figure 3-6, E) 41
3-14 Installation 44
Connecting to the Network 46
Connections 47
3-18 Installation 48
3 UTP RJ45 cable connector 49
3-20 Installation 50
Devices 51
2 Other device port 52
3 Release tab 54
What Is Needed 56
Mode 7 Bit Control 57
Transmit Transmit=9600 57
Bits Parity 8 Bits, No Parity 57
Stop Bit 1 Stop Bit 57
3-28 Installation 58
Connecting to a Modem 59
3-30 Installation 60
RJ45 DB9 61
RJ45 DB25 61
Completing the Installation 62
in the Matrix DFE-Platinum 63
3-34 Installation 64
3-36 Installation 66
Troubleshooting 67
Using LANVIEW Diagnostic LEDs 68
4-2 Troubleshooting 68
Table 4-1 LANVIEW LEDs 69
Troubleshooting Checklist 70
4-6 Troubleshooting 72
Instructions) 73
4-8 Troubleshooting 74
Specifications 75
7G4280-19 Specifications 76
A-4 Specifications 78
COM Port Pinout Assignments 81
Regulatory Compliance 82
Required Tools 83
Setting the Mode Switches 83
1 Mode switch pack 84
Memory Locations 85
Memory Replacement Procedures 85
Removing the DRAM SIMM 87
Installing the DRAM SIMM 88
DIMM Replacement Procedure 89
Installing the DIMM 90

Comentarios a estos manuales

Sin comentarios

Enterasys Matrix N7 7C107 Guía de instalación Pagina 51

Comentarios a estos manuales

Relacionado con productos y manuales para Redes Enterasys Matrix N7 7C107