Enterasys Matrix 7GR4202-30 Guía de instalación Pagina 42
- Pagina / 92
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Installing Optional Mini-GBICs
3-14 Hardware Installation
To prepare and install a Mini-GBIC into the 1G-2MGBIC, proceed as follows:
Preparation
Before installing the Mini-GBIC, proceed as follows:
1. Attach the antistatic wrist strap (refer to the instructions in the antistatic wrist strap package)
before removing the Mini-GBIC from the antistatic packaging.
2. Remove the Mini-GBIC from the packaging.
3. If there is a protective dust cover (see Figure 3-6,
➄) on the Mini-GBIC port, do not remove it
at this time.
Installation
To install a Mini-GBIC, refer to Figure 3-6 and proceed as follows:
1. Hold the Mini-GBIC
➀ with its top side ➁ facing up and its 7-pin edge connector ➂ facing the
1G-2MGBIC
port slot ➃ as shown in Figure 3-6.
2. Carefully align the Mini-GBIC
➀ with the 1G-2MGBIC port slot ➃.
3. Push the Mini-GBIC
➀ into the port slot ➃ until the Mini-GBIC “clicks” and locks into place.
Figure 3-6 Mini-GBIC Installation
➀ Mini-GBIC ➃
1G-2MGBIC Port Slot
➁ Mini-GBIC, Top Side ➄ Mini-GBIC, Protective Dust Cover
➂
7-Pin Edge Connector (insertion side)
➅
Locking Tab
Â
Å
Á
À
36801_16
1G-2MGBIC
Ã
Ä
- Matrix E1 Series 1
- (1H582-25 and 1H582-51) 1
- Installation Guide 1
- FCC NOTICE 4
- INDUSTRY CANADA NOTICE 4
- VCCI NOTICE 4
- CLASS A ITE NOTICE 4
- SAFETY COMPLIANCE 5
- SAFETY INFORMATION 6
- CLASS 1 LASER TRANSCEIVERS 6
- ENTERASYS NETWORKS, INC 7
- PROGRAM LICENSE AGREEMENT 7
- DECLARATION OF CONFORMITY 10
- Contents 11
- TROUBLESHOOTING 12
- SPECIFICATIONS 12
- GBIC SPECIFICATIONS 13
- About This Guide 17
- STRUCTURE OF THIS GUIDE 18
- HOW TO USE THIS GUIDE 19
- RELATED DOCUMENTS 19
- DOCUMENT CONVENTIONS 20
- Introduction 21
- 1H582-51 22
- 1H582-25 22
- 1.2 CONNECTIVITY 23
- 1G-2GBIC 24
- 1.3 STANDARDS COMPATIBILITY 25
- 1.4 GETTING HELP 25
- Network Requirements 27
- 2.2 10BASE-T NETWORK 28
- 2.3 100BASE-TX NETWORK 28
- 2.4 100BASE-FX NETWORK 28
- 2.5 1000BASE NETWORK 28
- Hardware Installation 29
- 3.2 UNPACKING THE DEVICE 30
- 3.3 INSTALLING OPTIONS 31
- 1H582-51 shown 33
- Coverplate 33
- Coverplate Captive Screws (2) 33
- Front Panel 33
- 1G154-09 34
- 3.5 INSTALLING OPTIONAL GBICs 35
- 3.5.1 Side Clip GBICs 36
- 3.5.2 Locking Bar GBICs 38
- Preparation 39
- Installation 39
- Installing Optional GBICs 40
- 3-12 Hardware Installation 40
- Removing the Mini-GBIC 43
- 3.7 INSTALLING THE DEVICE 44
- 3.7.1 Rackmount Installation 44
- 3.7.1.2 Installation 45
- ➁ in the rackmount kit 46
- ➁ (user supplied) 47
- 3.7.4 Connecting Power 48
- 3.8 CONNECTING TO THE NETWORK 49
- 3.8.1 Connecting UTP Cables 49
- Connecting to the Network 50
- 3-22 Hardware Installation 50
- Hardware Installation 3-23 51
- Multimode Fiber Optic Cables 54
- ➀, key side down ➁, into the 55
- • Transmit (TX) 56
- • Receive (RX) 56
- Hardware Installation 3-29 57
- 3.9.1 What Is Needed 58
- Hardware Installation 3-31 59
- Parameter Setting 59
- 3-32 Hardware Installation 60
- 3.9.4 Connecting to a Modem 61
- DB9 Connector (Female) 62
- Completing the Installation 63
- Hardware Installation 3-35 63
- RJ45 DB25 63
- “Getting Help” in Chapter 1 64
- Troubleshooting 65
- 4.1 USING LANVIEW 66
- Using LANVIEW 67
- Troubleshooting 4-3 67
- Table 4-1 LANVIEW LEDs 67
- 4.2 TROUBLESHOOTING CHECKLIST 68
- Troubleshooting Checklist 69
- Troubleshooting 4-5 69
- 4-6 Troubleshooting 70
- 4.3 USING THE RESET BUTTON 71
- Specifications 73
- (Section A.1) 73
- A-2 Specifications 74
- Item Specification 74
- SC fiber optic connection 76
- A.5 REGULATORY COMPLIANCE 77
- Optional Installations and 79
- Mode Switch Bank Settings 79
- ÑOS, AL IGUAL QUE AL APARATO 80
- 12 Cover Screws 81
- 1H582-51 Device (shown) 81
- B.3 SETTING THE MODE SWITCHES 82
- Setting the Mode Switches 83
- B.4.1 Locating SIMMs 84
- B.4.2 Removing the DRAM SIMM 84
- Release Tabs 85
- DRAM SIMM 85
- Connector 85
- SIMM Alignment Notch 86
- Connector Fingers 86
- SIMM Alignment Notches (2) 86
- Connector Clips 86
- GBIC Specifications 87
- C.3 REGULATORY COMPLIANCE 90
Relacionado con productos y manuales para Los conmutadores de red Enterasys Matrix 7GR4202-30
(51 paginas)
(7 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.075 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales